Eicon Networks Network Card 64 0074 02 User Manual

Physical Description  
1. RJ-48C jacks: Connectors to external  
digital telephone network interface.  
CH4 CH3 CH2CH1  
8
Red  
Yellow  
Green  
2. General Network Interface Alarm LED  
3. Power LED  
Dialogic®  
4. Reset LED  
Loopback  
5. SW1: Rotary switch to set board  
7
DM/V600A-2E1-PCI  
identification (Linux systems only).  
6
6. Alarm LEDs: During power-up, indicate  
Power on Self Test (POST) status. During  
operation CH1 and CH2 LEDs indicate  
network alarms for each trunk.  
Red—Alarm to indicate loss of signal  
Yellow—Alarm to indicate loss of frame  
synchronization at far end of external  
network  
Media Board  
9
Quick Install Card  
5
10  
Part Number 64-0074-02  
Green—Indicates signal present; powered  
up and receiving signal from external E1  
sources  
Loopback—Indicates loopback mode is  
activated  
Copyright © 2001-2007  
Dialogic Corporation.  
All rights reserved.  
4
3
2
1
7. CT Bus/MVIP Bus Termination Jumpers:  
Bus signal is terminated when the  
1
2
corresponding jumper clip is installed.  
Note: Signal must be terminated only on  
boards at each end of the CT Bus cable.  
JP2A—CT Bus termination jumper  
JP2A  
JP2B  
Before You Begin  
JP2B—MVIP Bus termination jumper  
Protecting the Board from Damage  
8. P3: CT Bus connector  
9. ISA Edge Retainer  
10.Signal Processing Daughterboard  
CAUTION: All computer boards are sensitive to  
electrostatic discharge (“ESD”). Handle all static-  
sensitive boards and components at a static-safe work  
area, and observe anti-static precautions at all times.  
Linux Systems  
Configuring the Hardware  
In a Linux system, you must set SW1 to a unique  
number for each installed board. Use a non-magnetic  
screwdriver to turn SW1 to one of 16 board ID settings,  
0–9 or A–F.  
If you are not familiar with ESD safety precautions, visit  
Board Identification  
The device driver, part of the system software, assigns  
board instance numbers in ascending order (beginning  
with 0) as it detects each board in your system. A board  
instance number is the identification (ID) number used by  
the system software to recognize the board.  
Unpacking the Board  
After the hardware and the system software are installed,  
refer to the proper configuration files to retrieve the  
assigned board instance ID number(s). For more  
information about Linux configuration files, see the  
Dialogic® System Software documentation.  
Unpack the Dialogic® DM/V600A-2E1-PCI Media Board  
(“board”) according to the following steps:  
1. Prepare a static-safeguarded work area.  
2. Carefully remove the board from the shipping  
carton and anti-static packaging. Handle the  
board by the edges and avoid touching the  
board’s components.  
3. Lay the board on the static-dissipative work  
surface.  
Note: Place boards in static-shielding bags when  
carrying boards from station to station.  
Note: If you add or remove a board, the system may  
change the existing board instance numbers, depending  
upon the PCI bus and slot number where the board is  
installed or removed.  
Installing the Hardware  
1. With your computer on the static-safe work area,  
switch off the power and disconnect all power cords  
from the electrical outlets.  
Windows Systems  
system automatically assign board instance numbers by  
PCI bus slot number.  
2. Remove the computer cover.  
3. Select an empty PCI expansion bus slot and remove  
the slot’s retaining screw and access cover plate (if  
applicable).  
After the hardware and the system software are installed,  
refer to the Dialogic® Configuration Manager (DCM)  
utility to retrieve the assigned board instance ID  
number(s). For more information about board  
identification, see the DCM online help.  
CAUTION: Do not remove the board from the anti-static  
packaging until you are ready to install it. Observe  
proper anti-static precautions at all times.  
4. If you are not installing your board in an ISA form  
factor PCI slot, remove the ISA edge retainer.  
 

Euro Pro Carpet Cleaner EP63CH User Manual
Everpure Water System CB20 124E User Manual
Extron electronic Network Card 066 01 User Manual
Fisher Paykel Garbage Disposal WD1001 User Manual
Frigidaire Washer 134489700A 0501 User Manual
Gateway Network Card M250 User Manual
GE Air Conditioner AZ85E18DAC User Manual
GE Microwave Oven ZE2160SF User Manual
Gemini CD Player CDJ 30 User Manual
GE Mixer 169160 User Manual