GE Fan BFL125UQ User Manual

BFL125UQ  
Ultra Quiet Bath Fan with Light/Night Light Users Guide  
Item Stock Number(s): BFL125UQ  
READ AND SAVE THESE INSTRUCTIONS  
Caution: For general ventilating use only. Do not use to exhaust hazardous or explosive  
Important Safety Instructions  
materials and vapors.  
CAUTION: The equipment covered by these instructions should be installed and serviced  
Warning: Do not use in kitchens.  
only by competent personnel utilizing proper safety practices and procedures. These  
instructions are written for such personnel and are not intended as a substitute for adequate  
training and experience in safe procedures for this type of equipment.  
To ensure the best air and sound performance, it is recommended that the length of ducting  
and the number of elbows be kept to a minimum, and that insulated hard ducting be used.  
Larger duct sizes will reduce noise and airflow restriction.  
Warning: Disconnect the power at service panel before beginning this installation.  
Before beginning this installation remove the fans  
blower housing (which includes the motor, blade, bracket  
and motor plate) assembly by removing the screw which  
secures the motor plate housing to the fan housing  
(Fig. 1). Place this assembly and the grill in the carton  
until needed so they do not get damaged.  
Fig. 1  
Caution: To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. Do  
not vent exhaust air into spaces within walls or ceilings, or into attics, crawl spaces, or garages.  
Acceptable for use over tub or shower when installed in a GFCI protected branch circuit.  
Warning: To reduce the risk of fire or electric shock, do not use this fan with any solid-  
state speed control device.  
Warning: To reduce the risk of fireor electric shock or injury to persons, observe the following:  
Mounting the Housing: New Construction  
Using the Hanging Brackets (Fig. 2)  
a) Use this unit only in the manner intended by the manufacturer. If you have any questions,  
please contact the manufacturer.  
b) Before servicing or cleaning unit, switch power to off at service panel and lock the service  
disconnecting means to prevent power from being switched on accidentally. When the  
service disconnecting means cannot be locked, securely fasten a prominent warning  
device, such as a tag, to the service panel.  
1. Insert the hanging brackets in the slots provided in  
the housing.  
2. Select the most convenient electrical knockout  
and remove it, then locate the fan housing between  
joists so that the bottom of the fan housing is level  
with the planned finished ceiling.  
c) Do not install this fan in a ceiling thermally insulated to a value greater than R-40  
3. Use screws or nails (not provided) to secure the  
hanger bars to the ceiling joists.  
d) Installation work and electrical wiring must be done by qualified, competent, trained  
person(s) in accordance with all applicable codes and standards using proper safety  
practices, including fire-related construction.  
Fig. 2  
Mounting the Housing: Existing Construction  
e) Sufficient air is needed for proper combustion and exhausting of gases through the flue  
(chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment  
manufacturers guideline and safety standards such as those published by the National  
Fire Protection Agency (NFPA) and the American Society for Heating, Refrigeration, and  
Air Conditioning Engineers (ASHRAE), and the local code authorities.  
f) When cutting or drilling into a wall or ceiling, ALWAYS identify hidden electrical wiring  
and other hidden utilities in advance, to avoid damage.  
1. Determine the desired location for the fan.  
2. Drill asmall hole through the ceiling at the chosen location. Stick the end of a coat hanger  
through the hole into the attic to help locate the spot in the attic.  
3. Check the chosen area from above to make sure that the wiring can be installed and that  
the installation will not interfere with any existing wiring. Then select the most convenient  
electrical knockout and remove it.  
g) Ducted fans must always be vented to the outdoors.  
h) NEVER place a switch where it can be reached from the tub or shower.  
4. From above, position the housing between ceiling joists, and use the housing as a template  
to mark the required cut out in the ceiling.  
 

Extron electronic Stereo System DMP 64 User Manual
Extron electronic Switch TPX 88 User Manual
Fisher Paykel Ventilation Hood HC60PCHTX2 User Manual
FoodSaver Food Saver GameSaver Pro User Manual
Freecom Technologies Computer Drive FHD xx User Manual
FUNAI Blu ray Player MBP5130 F7 User Manual
Fundex Games Games Shoot the Moon User Manual
GE Dishwasher 165D4700P371 User Manual
Generac Portable Generator 005982 0 User Manual
GE Range ZGG24L20 User Manual