GE Universal Remote 24962 User Manual

24962  
Universal Remote  
Instruction Manual  
 
Setup  
Battery Installation  
1. On the back of the remote, push down on the  
tab and lift the cover off.  
2. Match the batteries to the + and - marks inside  
the battery case, then insert 2 AAA Alkaline  
batteries.  
3. Press the battery cover back into place.  
Battery Saver  
Your remote automatically turns off if the buttons  
are depressed more than 30 seconds. This will  
save your batteries should your remote get stuck in  
a place where the buttons remain depressed (e.g.,  
between the sofa cushions).  
Code Saver  
You will have up to 10 minutes to change the  
batteries in your remote without losing codes you  
have programmed. However, do not press any  
buttons until batteries are installed in the remote.  
If buttons are pressed without batteries in the  
remote, all codes will be lost.  
Code Setup  
The SETUP button is used to setup the remote.  
You can either setup the remote using the code  
for your brand of product, from the code tables (on  
separate sheet), or you can search through the  
library of codes until you find a code that works for  
your product. Please refer to “Code Search” page  
8 for more information on using the code search  
feature to learn how to search through the library  
of codes for your products. NOTE: You can store  
any kind of code under any mode (except TV). I.e.,  
you can store a DVR code under the SAT/CBL  
button, or a cable code under the DVD button, etc.  
However, you can only store TV codes under the  
TV button.  
3
 
Button Functions  
Some buttons on the remote might have functions that  
are referred to by different names on the device you are  
controlling. E.g., PREV. CH may be called RECALL,  
or ENTER may be called DISPLAY. These differences  
depend on the brand and model of your product. Also,  
this remote can only operate features that exist on your  
product. E.g., your product must have PREV. CH ability  
for the PREV. CH button to operate this feature.  
TV, DVD, SAT/CBL Selects  
product to be operated.  
SETUP For setup.  
SHIFT Accesses  
shifted functions.  
MUTE Turns off the  
TV sound while the  
picture remains.  
OK Selects menu  
items for the device  
you are controlling.  
INFO button brings up  
DVD Display or Control  
Menu for Chapter/  
Track/Title number,  
Time remaining/elapsed  
indication, system  
information, etc.  
MENU  
Selects the on-screen  
menu.  
DOT Used to  
select digital chan-  
nels, e.g., 2.3.  
RECORD, PLAY, STOP,  
REW, FF, PAUSE oper-  
ate your DVD or DVR  
even when the remote  
is set to operate the TV.  
Also operates DVD/DVR  
Scan -/+.  
 
Button Functions, cont.  
Red Indicator  
ON-OFF Turns  
Lights when any  
button is pressed.  
device On or Off.  
INPUT  
For some TVs, press  
repeatedly to select  
from available viewing  
sources (antenna, cable  
box, DVD, etc.).  
CHANNEL Up/Down  
Changes the channels.  
VOLUME UP/DOWN  
Changes the volume  
level of the product,  
normally the TV.  
PREV. CH Returns to  
the previously  
selected channel.  
EXIT Exit On-Screen  
Menus and/or Return  
to previous On  
Screen selection.  
NUMBERS  
Enter numbers for direct  
channel selection. Some  
products require ENTER  
to be pressed after  
channel selection.  
ENTER  
For some TV models,  
used after direct  
channel number  
entry to immediately  
change to the  
selected channel.  
Note: The REC button must be pressed TWICE to record  
from your DVR. For some brands of DVRs, you might  
need to press the REC button once, then press it again  
for three seconds.  
5
 
SHIFT Function  
Press SHIFT (Setup) prior to the shifted key func-  
tion, e.g., for MENU - press and release SHIFT  
(Setup) then MENU (Info).  
UP - press and release SHIFT then UP (Chan+).  
DOWN - press and release SHIFT then DOWN  
(Chan-).  
LEFT - press and release SHIFT then LEFT (Vol-).  
RIGHT - press and release SHIFT then RIGHT  
(Vol+).  
OK - press and release SHIFT then OK (Mute).  
EXIT - press and release SHIFT then EXIT (Prev.  
Ch).  
The red indicator blinks for each key press.  
6
 
Direct Code Entry  
1. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
2. Press and release the desired mode  
button (TV, DVD, etc.). The red indicator  
blinks, then stays lit.  
3. Enter the 4-digit code  
from the code tables  
(on separate sheet).  
Note: after a valid code  
entry, the red indicator  
turns off. For an invalid  
code, the red indicator  
flashes.  
4. With your device on, press ON/  
OFF. If the device turns off, no  
further programming is required.  
Note: If some buttons do not  
operate your equipment, try one  
of the other codes for your brand.  
Write your codes down here for easy reference  
later.  
Device  
Device stored Code  
TV  
TV  
DVD  
SAT/CBL  
7
 
Code Search  
If your device does not respond after you have  
tried all the codes for your brand, or if your brand is  
not listed, try searching for your code by following  
these steps.  
1. Manually turn on the device (TV, DVD, etc.) to  
be controlled.  
2. Press and hold the SETUP button until  
the red indicator stays on, then release  
the SETUP button.  
3. Press and quickly release the desired  
mode button (TV, DVD, etc.). The red  
indicator blinks off once.  
4. Press the CHAN+ button  
repeatedly (up to 300 times)  
until the device to be controlled  
changes channel. The red  
indicator blinks off with each  
button press. If you accidentally overshoot  
the code required, press the CHAN- button to  
backtrack through the library until the device  
changes channel. Pressing CHAN+ changes  
direction to forward again.  
5. Press and release ENTER to install the  
code.  
Most users will store DVD codes under the DVD button,  
and Satellite or Cable codes under SAT/CBL. If (for ex-  
ample) you want to store a DVR code under SAT/CBL,  
first follow the procedure for Direct Code Entry (page  
8) and press SAT/CBL in step 2 of Direct Code Entry,  
then enter ANY DVR code in step 3 of Direct Code Entry.  
Then follow the steps above for Code Search.  
Note: If the device does not have a CHAN+ button, use  
PLAY (DVD/DVR/VCR only) or POWER instead. Code  
Search starts from the currently stored 4 digit number  
under that mode. Sometimes the first code that “works”  
with your device may only allow limited functionality  
(e.g., the MENU button might not work). There may be  
a code that performs more functions. Continue the code  
search process until the best code is found.  
8
 
Code Identification  
The Code Identification Feature allows you to  
identify the 4-digit library code stored under your  
device key. For example, if you want to find out  
what 4-digit code is stored under your TV device  
key, follow the six steps below:  
1. Press and hold the SETUP button until  
the red indicator stays on. Release the  
SETUP button.  
2. Press and release the desired mode  
button (TV, DVD, etc.). The red  
indicator blinks, then stays lit.  
3. Press and release the SETUP button.  
The red indicator blinks once and  
remains lit.  
4. To nd the first digit for  
the code stored under  
the mode key pressed  
in step 2, press each  
numeric key from 0-9 in  
turn. The number that  
causes the indicator  
light to blink is the first  
digit in your code.  
5. To nd the second digit, repeat step 4.  
6. Repeat step 4 again to find the third and fourth  
digits. This time the red indicator turns off and  
stays off.  
9
 
Using Your Remote  
Controlling Devices with Separate  
Power On and Off Buttons  
Some GE, RCA and ProScan models require  
you to press the device button for more than one  
second to turn the device on and the POWER  
button to turn the device off.  
Controlling Combo Devices  
Some Combo devices (e.g., TV/DVR, TV/DVD,  
DVD/DVR, etc.) will require you to set up two  
different Mode buttons to control both parts of the  
Combo device. For example, if you have a TV/  
DVD Combo, you might need to set up one code  
under the TV button to control the TV part AND a  
separate code (under any other Mode button) to  
control the DVD part.  
DVR/DVD Punch-Through  
This remote allows the 6 DVD/VCR transport  
buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,  
and REC) to Punch-through from any Mode  
programmed with TV, SAT or Cable codes to the  
last DVD, or VCR programmed Mode you used,  
i.e., the transport keys control your DVD or VCR  
player even when you are in TV, SAT or Cable  
mode. If you use a SAT/DVR, Cable/DVR, etc., you  
may want to disable this Punch-through feature  
to allow the transport keys to control your DVR  
device. The following steps will disable the punch-  
through feature:  
1. Press and hold SETUP until the red indicator  
stays on, then release the SETUP button.  
2. Press and hold PAUSE until the red indicator  
turns off, then release the PAUSE button. The  
PAUSE button needs to be held held for about  
3 seconds before the red indicator turns off.  
The punch-through feature can be enabled again  
by repeating the above steps.  
10  
 
Using Your Remote, cont.  
Volume/Mute Control and Punch-  
Through  
This remote lets you select which device Mode  
controls your Volume/Mute buttons. The remote is  
initially set for all device Modes to use their own  
Volume/Mute control if present. If the programmed  
code has no Volume/Mute operation of its own  
then those buttons will punch-through control to  
the TV Mode device without needing to change to  
TV Mode.  
Setting ALL Volume/Mute Control to  
any one Mode  
This routine can set all Modes to “punch-through”  
to any one chosen Mode for Volume/Mute button  
control without the needing to change to that  
Mode.  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
the button.  
2. Press and hold the MUTE button until  
the red indicator blinks off, then release  
the button.  
3. Press and release the desired Mode button  
(TV, DVD, etc.) for Volume/Mute control,  
the red indicator blinks then stays on.  
4. Press and release the MUTE button  
and the red indicator turns off. The  
red indicator will blink rapidly for  
three seconds if the Mode you have  
selected has no Volume/Mute control.  
All other Modes will now punch-through to your  
chosen Mode for Volume/Mute control.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Using Your Remote, cont.  
Setting any Mode to use its own  
Volume/Mute Control  
This routine can set any Mode to use only its own  
Volume/Mute control. Note - If your chosen Mode  
has no Volume/Mute functions of its own then the  
Volume/Mute buttons will do nothing.  
1. Press and hold the SETUP button until  
the red indicator turns on, then release  
the button.  
2. Press and hold the MUTE button until  
the red indicator blinks off, then release  
the button.  
3. Press and release the desired Mode  
button (TV, DVD, etc.), the red indicator  
blinks then stays on.  
4. Press and release the VOL- button,  
the red indicator blinks then stays on.  
5. Press and release the MUTE button and  
the red indicator turns off.  
Your chosen Mode will now use its own Volume/  
Mute control.  
12  
 
Troubleshooting  
Remote does not operate your product.  
Press the mode button of the product you want  
to control.  
Program the remote with a new code.  
Install new batteries. (You might have to  
reprogram your remote after installing new  
batteries.)  
Remote may not be compatible with your  
product.  
Remote does not operate some  
features of your product.  
Sometimes a particular code might operate  
some features but not all. Try programing  
remote with a new code.  
Remote may not be able to operate all features  
of your product or button names might be  
different than your product.  
Red Indicator blinks after you program  
a product code.  
Remote did not accept the code.  
Try to program the code again or try a different  
code.  
Lost Your Codes?  
Enclosed with this remote is a sticker on which  
you should write the codes for each device you  
programmed. Apply the sticker to the back of  
the remote or somewhere convenient for future  
reference.  
Also on the sticker is our website address which,  
should you lose your codes or programming  
instructions, you can find available on our website:  
13  
 
90 Day Limited Warranty  
Jasco Products Company warrants this product  
to be free from manufacturing defects for a period  
of ninety days from the original date of consumer  
purchase. This warranty is limited to the repair  
or replacement of this product only and does not  
extend to consequential or incidental damage to  
other products that may be used with this unit.  
This warranty is in lieu of all other warranties  
express or implied. Some states do not allow  
limitations on how long an implied warranty lasts  
or permit the exclusion or limitation of incidental or  
consequential damages, so the above limitations  
may not apply to you. This warranty gives you  
specific rights, and you may also have other rights  
which vary from state to state. If unit should prove  
defective within the warranty period, return prepaid  
with dated proof of purchase to:  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114-2205  
14  
 
15  
 
24962  
Universal Remote  
Instruction Manual  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114-2205  
Made in China  
24962-03/10  
 

Elation Professional TV Cables 30 24 004 1262 User Manual
Excalibur electronic MP3 Player 191 User Manual
Fisher Price Automobile Parts C2474 User Manual
Fisher Price Baby Accessories P6033 User Manual
Fisher Price Baby Toy B8728 0920 User Manual
Frigidaire Air Conditioner FRA082AT7 User Manual
Fundex Games Board Games CALAMITYVILLE User Manual
GE Home Security System NX 108 116 124E User Manual
GE Washer GTWN2800DWW User Manual
GE Water Heater GN75DNSRSA User Manual